Can I Install a Bath Tub Myself? Factors to Consider And Actions
Can I Install a Bath Tub Myself? Factors to Consider And Actions
Blog Article
We've found this article on Installing A Bathtub directly below on the net and figured it made good sense to relate it with you on my blog.
Installing a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily easily accessible, the task can relocate quickly; if you have to open up a wall surface to get rid of the old tub and position the brand-new bath tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified on your own for the work and also are comfortable attempting it. Rather than employing a specialist to take over a halfway-completed job, it is much better to think about utilizing one prior to you start. Possibilities are you may need an expert plumber to make tube connections.
This post will certainly assist you set up a brand-new tub in your shower room if you have already purchased a new tub and don't require to transform the setup of your previous water pipelines.
Your tools as well as material checklist ought to comprise the following:
Getting ready for the Installation
Firstly, the supporting structure provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to ensure that if the tap comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted accessibility that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Utilizing both wood boards under its feet, place the tub in the called for placement. The wooden boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the level reads level.
To set up taps, fit all-time low of the furthest adaptable tap port to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the supply of water as well as examine all joints and new pipework for leaks and also tighten them if essential. Load the bathtub as well as additionally check the overflow outlet as well as the normal electrical outlet for leaks.
Finally, fix the bath paneling as explained in the maker's instruction manual. Tiling and securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will settle it into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will require reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin ensuring that the washing machines remain in place between the tap and the sink. Secure the faucet in position with the manufacturer provided backnut. Once the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind should be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can split rather early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily offered on the market. It is a good idea to fit the tiles utilizing water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that blog posting about Installing A Bathtub when doing a lookup on the search engines. Sharing is nice. Who knows, you might be helping someone out. Many thanks for your time. Visit us again soon.
Need Help? Hire Us Now!
Report this page